Dr. - Ing.  Nikolaos I. Galanis

Mechanical Engineer A.U.Th.

Laboratory Cooperator

Laboratory of Manufacturing Technology

National Technical University of Athens                                                                                                                                                                                                                                                                    EL  |  EN  |  DE   

 

General

CV

Publications

Communication

Links

 

 

Below, there are listed my publications classified in three groups, International Journal publications, International conferences and Books or books chapters. For any information about them, do not hesitate to come in contact with me.

International Journals

1.            Galanis, N.I. and Manolakos, D.E. (2009) ‘Surface roughness of manufactured femoral heads with high speed turning’, Int. J. Machining and Machinability of Materials, Vol. 5, No. 4, pp.371–382

2.            Nikolaos I. Galanis and Dimitrios E. Manolakos (2010) ‘Surface roughness prediction in turning of femoral head’, Int J Adv Manuf Technol, Vol. 51, Issue 1, pp. 79- 86, DOI 10.1007/s00170-010-2616-4

3.            Nikolaos I. Galanis and Dimitrios E. Manolakos (2010) ‘Forces measurement in turning of femoral heads from AISI 316l stainless steel’, Journal of Manufacturing Technology Research, Volume 2, Issue 1/2, pp. 1–15

4.            K. Gourgouletis, N.M. Vaxevanidis, N.I. Galanis and D.E. Manolakos (2011) 'Electrical Discharge Drilling of Carbon Fibre Reinforced Composite Materials', Int. J. Machining and Machinability of Materials, Vol. 10, No. 3, pp. 187–201.

5.            A.P. Markopoulos, K. Kantzavelos, N. Galanis and D.E. Manolakos (2011) '3D Modeling of Precision High Speed Turning and Milling for the Prediction of Chip Morphology using FEM', Journal of Machining and Forming Technologies, Volume 3, Issue 3/4, pp. 149-162

6.            A.P. Markopoulos, K. Kantzavelos, N.I. Galanis and D.E. Manolakos (2011) '3D Finite Element Modeling of High Speed Machining', International Journal of Manufacturing, Materials and Mechanical Engineering, Volume 1, Issue 4, pp. 1-18

7.            Galanis, N.I., Markopoulos, A.P., Giannakopoulos, I.D., Manolakos, D.E. (2013) 'Manufacturing of femoral heads from Ti-6Al-4V alloy with high speed machining: 3d finite element modelling and experimental validation', Manufacturing Technology, Volume 13, Issue 4, pp. 437-444 

8.      N.I. Galanis, A.P. Markopoulos, A. Kagkelaris, C. Kastritsis and D.E. Manolakos (2014) ‘On the Influence of Processing Conditions on Surface Roughness for Milling Titanium Alloys with HSS Tools’ , Journal of Manufacturing Technology Research, Volume 6, Issue 3/4, pp. 113–124

9.        Michail D. Mentzos, Angelos P. Markopoulos, Nikolaos I. Galanis, Dionissios P. Margaris, Dimitrios E. Manolakos (2015) 'Design, Numerical Analysis and Manufacture of Radial Pump Impellers with Various Blade Geometries', International Review of Mechanical Engineering (I.RE.M.E.) Volume 9, No. 1, pp. 104-111

10.      Angelos P. Markopoulos, Witold Habrat, Nikolaos I. Galanis, Nikolaos E. Karkalos (2015) ‘Effect of Tool model on Result of finite element simulation of high speed machining (HSM)’ Advances in Manufacturing Science and Technology, Vol. 39 No. 4, pp. 23-35

11.     Karkalos, N.E., Galanis, N.I., Markopoulos, A.P. (2016) ‘Surface roughness prediction for the milling of Ti-6Al-4V ELI alloy with the use of statistical and soft computing techniques’ Measurement: Journal of the International Measurement Confederation Vol. 90, pp. 25-35.

12.   AP Markopoulos, NI Galanis , NE Karkalos, , DE Manolakos (2018) ‘Precision CNC Machining of Femoral Component of Knee Implant: A Case Study, Machines 2018, 6(1), 10; https://doi.org/10.3390/machines6010010

International Conferences

  1. N. I. Galanis, D. E. Manolakos, N. M. Vaxevanidis (2008) 'Comparison between Dry and Wet Machining of  Stainless Steel', Proceedings of the 3rd International Conference on Manufacturing Engineering (ICMEN), 1-3 October, Chalkidiki, Greece

  2. N. I. Galanis, S. L. Afsaridis, S. N. Vlachostathopoulos, D. E. Manolakos (2008) 'Manufacturing Process with the Use of Protocol STEP-NC', Proceedings of the 3rd International Conference on Manufacturing Engineering (ICMEN), 1-3 October, Chalkidiki, Greece

  3. Nikolaos I. Galanis and Dimitrios E. Manolakos (2009) ‘Design, numerical analysis and manufacturing of artificial hip joint implants’ SEECCM 2009 2nd South-East European Conference on Computational Mechanics, An IACM-ECCOMAS Special Interest Conference Rhodes, Greece, 22–24 June

  4. Nikolaos I. Galanis and Dimitrios E. Manolakos (2009) ‘Investigation of Cutting Parameters in Manufacturing of Femoral Heads’ Proceedings of the World Congress on Engineering 2009 Vol II pp. 1606- 1611, WCE 2009, July 1 - 3, London, U.K.

  5. N.M. Vaxevanidis, N. Galanis, G.P. Petropoulos, N. Karalis, P. Vasilakakos and J. Sideris (2010) 'Surface Roughness Analysis in High Speed-Dry Turning of Tool Steel', Proceedings of ESDA2010: 8th Biennial ASME Conference on Engineering Systems Design and Analysis, July 12-14, Instabul, Turkey. (paper ESDA2010-24811)

  6. Georgios N. Kouzilos, Nikolaos I. Galanis and Dimitrios E. Manolakos (2011) ‘Modeling of three-dimensional flow, Heat transfer and Stress analysis in HDPE extrusion die’ Proceedings of the 7th GRAMC, 30 June – 2 July, Athens, Greece  

  7. Nikolaos I. Galanis and Dimitrios E. Manolakos (2011) ‘Design of a Hip Joint Simulator According to the ISO 14242’ Proceedings of the World Congress on Engineering 2011 Vol. III pp. 2088 - 2093,WCE 2011, July 6 - 8, London, U.K.

  8. D. Tzamouranis, N. M. Vaxewvanidis, N. I. Galanis, D. E. Manolakos (2011) 'Electrical Discharge Machining of Tungsten Carbides', Proceedings of the 4rd International Conference on Manufacturing Engineering (ICMEN), 3-5 October, Thessaloniki, Greece

  9. Nikolaos I. Galanis and Dimitrios E. Manolakos (2014) ‘Finite element analysis of the cutting forces in turning of femoral heads from AISI 316l stainless steel’, Proceedings of the World Congress on Engineering 2014 Vol. II pp. 1232 - 1237, WCE 2014, July 2 - 4, London, U.K.

  10. AP Markopoulos, NE Karkalos, NI Galanis, DE Manolakos (2017) ‘Design and Machining of the Femoral Component of Total Knee Implant’ Solid State Phenomena, Vol. 261, pp. 313-320

Books or book chapters

  1. Nikolaos I. Galanis and Dimitrios E. Manolakos (2010) ‘Manufacturing and examination of metallic femoral heads’ AIP Conference Proceedings, Volume 1220, pp. 67-77  

  2. Nikolaos I. Galanis and Dimitrios E. Manolakos (2010) ‘Forces measurement in turning of femoral heads from AISI 316l stainless steel’, Manufacturing Technology Research, Volume 2 (ed. J.P. Davim), Nova Science Publishers, Inc, New York, USA

  3. Nikolaos I. Galanis (2011) 'Ultra Precision Manufacturing of Artificial Biological Implants of Hip Joint' , PhD Thesis, N. T. U. A. (In order to read the summary of the Thesis press here)

  4. A.P. Markopoulos, K. Kantzavelos, N. Galanis and D.E. Manolakos (2011) '3D Modeling of Precision High Speed Turning and Milling for the Prediction of Chip Morphology using FEM', Machining and Forming Technologies Volume 3 (ed. J.P. Davim), Nova Science Publishers, Inc, New York, USA

  5. Apostolos Efthimiades, Nikolaos Galanis, Konstantina Kalliakoudi (2014) New technologies in heating - energy consumption, C.T.I. Diophantus book code 24-0498, Athens (in Greek)

  6. Nikolaos I. Galanis and Dimitrios E. Manolakos (2015) 'Analysis of the cutting forces in manufacturing stainless steel femoral heads using finite element method' Transactions on Engineering Technologies: World Congress on Engineering 2014, pp. 117-130, Springer, Netherlands

  7.  Angelos P. Markopoulos, Witold Habrat, Nikolaos I. Galanis and Nikolaos E. Karkalos (2016) ‘Modelling and Optimization of Machining with the Use of Statistical Methods and Soft Computing’ Design of Experiments in Production Engineering, Edition: 1st, Chapter: 2, Publisher: Springer International Publishing, Editors: J. Paulo Davim, pp.39-88

Publications in Greek Conferences

1.         Nikolaos Galanis and Dimitrios Manolakos (2008) ‘Materials and Process for manufacturing femoral heads for hip joints implants’,   4th Two-day Conference of Greek Association  of Biomaterials, Athens, 21 – 22 November (in greek)

2.          Nikolaos Galanis and Dimitrios Manolakos (2009) ‘Manufacture and inspection of ceramic femoral heads for hip joints implants’, 5th Pan-Hellenic Ceramic Congress, Athens, 22 – 23 October (in greek)

3.          Nikolaos Galanis and Dimitrios Manolakos (2009) ‘Inspection of femoral heads for hip joints implants’’ , 5th Conference of Greek Association  of Biomaterials, Athens, 27 – 29 November (in greek)

4.          Dimitrios Manolakos and Nikolaos Galanis (2010) ‘Machinability of femoral heads for hip joints implants’, 16th Seminar of Biomechanics of Spine and Biotechnology, Hellenic Association of Orthopaedic Surgery and Traumatology, 4 - 6 December (in Greek)

5.      Nikolaos Galanis and Dimitrios Manolakos (2013) Use of biomaterials in orthopedic' , 9th Pan-Hellenic Scientific Conference of Chemical Engineering, Athens 23-25 May (in Greek)

Patents 

  1. Nikolaos Galanis (2011) "Awning-driving mechanism provided with articulated joints and a canopy-folding system for airproof and waterproof construction" ΟΒΙ - Greek Patent No GR1007806

  2. Nikolaos Galanis (2012) "Aluminium Profile for the construction of Pergolas for larges areas " ΟΒΙ - Greek Patent Sketch No 6003546

  3. Nikolaos Galanis (2013) "Connection of aluminium profiles for the construction of great-surface pergolas" ΟΒΙ - Greek Patent No GR1008326