Ioannis Antoniadis
Professor
Director, Dynamics and Acoustics Laboratory (DAL)
Mechanical Design and Control Systems Division
 
School of Mechanical Engineering, National Technical University of Athens
Tel.: +30-210-7721524, Fax: +30-210-7721525, email: antogian@central.ntua.gr

LIST OF PUBLICATIONS

REFEREED SCIENTIFIC JOURNALS

J.60)

Kapasakalis, K.A., Antoniadis, I. A. and Sapountzakis, E.J., “Performance Assessment of the KDamper as a  Seismic Absorption Base”, Structural Control and Health Monitoring (accepted).
J.59)

G. Papaioannou, A.Voutsinas, D. Koulocheris, I. Antoniadis, 2019, Dynamic performance analysis of vehicle seats with embedded negative stiffness elements, Vehicle System Dynamics, to appear.
J.58)

S.Chapaloglou, A.Nesiadis, P.Iliadis, K.Atsonios, N.Nikolopoulos, P.Grammelis, C.Yiakopoulos, I. Antoniadis, E.Kakaras, 2019, “Smart energy management algorithm for load smoothing and peak shaving based on load forecasting of an island’s power system”, Applied Energy 238 (2019) 627–642.
J.57)

Sapountzakis I.E., Tranakidis P.G. and Antoniadis I. A. (2019) ‘’Implementation of the KDamper concept using disc springs’’, Journal of Low Frequency Noise, Vibration and Active Control. 2019, Vol. 38(1) 168–186, https://doi.org/10.1177/1461348418812318.
J.56)

S.Chapaloglou, A.Nesiadis, P.Iliadis, K.Atsonios, N.Nikolopoulos, P.Grammelis, C.Yiakopoulos, I. Antoniadis, E.Kakaras, 2019, “Smart energy management algorithm for load smoothing and peak shaving based on load forecasting of an island’s power system”, Applied Energy 238 (2019) 627–642.
J.55)

I. A. Antoniadis, A. Paradeisiotis, Acoustic Meta-materials Incorporating the KDamper Concept for Low Frequency Acoustic Isolation, Acta Acustica United with Acustica, Vol. 104, Iss.1 (2018).
J.54)

E.Sapountzakis, P.Syrimi,  A. Pantazis, I. A. Antoniadis, (2017), KDamper concept in seismic isolation of bridges with flexible piers. Engineering Structures. 153. 525-539. 10.1016/j.engstruct.2017.10.044.
J.53)

I. A. Antoniadis , V. Georgoutsos, A.Paradeisiotis, S.Kanarachos, K.Gryllias, 2017, “Implementation Assessment of a Wave Energy Converter, Based on Fully Enclosed Multi-axis Inertial Reaction Mechanisms. Discontinuity, Nonlinearity, and Complexity. 6. 445-463. 10.5890/DNC.2017.12.004.
J.52)

I. A. Antoniadis, K.J.Kyriakopoulos, E.G.Papadopoulos, 2017, “Hyper-damping behaviour of stiff and stable oscillators with embedded statically unstable stiffness elements”. International Journal of Structural Stability and Dynamics, 17. 1740008. 10.1142/S0219455417400089.
J.51)

C.Yiakopoulos, M.Koutsoudaki, K.Gryllias, I. A. Antoniadis, 2017, “Improving the performance of control charts for abnormal detection and classification”, Mechanical Systems and Signal Processing, 86. 122-150. 10.1016/j.ymssp.2016.09.036.
J.50)

I. A. Antoniadis, V. Georgoutsos, A. Paradeisiotis,"Fully enclosed multi-axis inertial reaction mechanisms forwave energy conversion", Journal of Ocean Engineering and Science, Volume 2, Issue 1, 2017, Pages 5-17.
J.49)

Chronopoulos D., Ampatzidis, Antoniadis I. A, 2016, “Enhanced acoustic insulation properties of composite metamaterials having embedded negative stiffness inclusions, Extreme Mechanics Letters, November 2016, DOI: 10.1016/j.eml.2016.10.012.
J.48)

K. Rodopoulos, I. A. Antoniadis, 2016, “Instantaneous fault frequencies estimation in roller bearings via wavelet structures, Journal of Sound and Vibration”, August 2016, DOI: 10.1016/j.jsv.2016.07.027.
J.47)

C.Yiakopoulos, K.Gryllias, M.Chioua, M.Hollender, I. A. Antoniadis,  2016, “An on-line SAX and HMM-based anomaly detection and visualization tool for early disturbance discovery in a dynamic industrial process”, Journal of Process Control 44:134-159 · August 2016.
J.46)

I. A. Antoniadis , Kanarachos S.A., Gryllias K. and Sapountzakis.I.,  2016, ”KDamping: A Stiffness Based Vibration Absorption Concept”, Journal of Vibration and Control, DOI:10.1177/1077546316646514.
J.45)

V.K. Dertimanis, I. A. Antoniadis,  E. Chatzi, 2016, “Feasibility analysis on the attenuation of strong ground motions using finite periodic lattices of mass-in-mass barriers”, ASCE Journal of Engineering Mechanics, DOI: 10.1061/(ASCE)EM.1943-7889.0001120.
J.44)

Chronopoulos D., Antoniadis I. A, Collet M., Ichchou,M, 2016, “Enhancement of wave damping within metamaterials having embedded negative stiffness inclusions”, Wave Motion, http://dx.doi.org/10.1016/j.wavemoti.2015.05.005.
J.43)

I. Antoniadis, D. Chronopoulos, V. Spitas, D. Koulocheris, 2015, “Hyper-damping properties of a stable linear oscillator with a negative stiffness element”, Journal of Sound and Vibration, V346, pp. 37-52.
J.42)

C.T.Yiakopoulos, J.Maczak, K. Rodopoulos, I. Antoniadis, 2014, “Multicomponent decomposition of a time-varying acoustic Doppler signal generated by a passing railway vehicle using Complex Shifted Morlet Wavelets”, Transportation Research Part C Emerging Technologies 07/2014; 44:34–51.
J.41)

I.A.Antoniadis, C. T. Yiakopoulos, K. C. Gryllias, K I. Rodopoulos, 2014, “IFESIS: Instantaneous Frequencies Estimation via Subspace Invariance properties of wavelet Structures”, Mechanical Systems and Signal Processing, Vol. 49, Issue 1-2 (2014), pp. 264-284.
J.40)

I. A. Antoniadis, D.T. Venetsanos, F.G. Papaspyridis, 2014, “Dynamic non-linear energy absorbers based on properly stretched in-plane elastomer structures”, Non-Linear Dynamics Journal, 75:367–386.
J.39)

C.Yiakopoulos, K. Rodopoulos, I. A. Antoniadis, 2014, “A parametric approach for the estimation of the instantaneous rotation speed of rotating machinery”, Mechanical Systems and Signal Processing, V44, Issue 1-2, 31-46.
J.38)

I. Antoniadis, K. Rododoulos, C. Yiakopoulos, 2013, ‘Multiple instantaneous frequency estimation using complex shifted Morlet wavelets’, International Journal of Condition Monitoring, Vol. 3, No. 2, pp. 42-46.
J.37)

I. A. Antoniadis, D.T. Venetsanos, F.G. Papaspyridis, 2013, “DIESYS - Dynamically non-linear dielectric elastomer energy generating synergetic structures: perspectives and challenges”, Smart Materials and Structures, 22 (2013) 104007.
J.36)

K. Gryllias, I. Antoniadis, 2013, ‘Estimation of the instantaneous rotation speed using complex shifted Morlet Wavelets’, Mechanical Systems and Signal Processing, Mechanical Systems and Signal Processing, Special Issue: Non-stationary Operations, Vol. 38, Issue 1 (2013), pp. 78-95.
J.35)

K. Gryllias, I. Antoniadis, 2012, ‘A Support Vector Machine approach based on physical model training for rolling element bearing fault detection in Industrial Environments’, Engineering Applications of Artificial Intelligence, V25(2), 326-344.
J.34)

C. Yiakopoulos, K. Gryllias, I. Antoniadis, 2011, ‘Rolling Element Bearing Fault Detection in Industrial Environments based on an K-means Clustering Approach’, Expert Systems with Applications, V38, 2888-2911.
J.33)

K. C. Gryllias, I. N. Koukoulis, C. T. Yiakopoulos, I. A. Antoniadis, and C. G. Provatidis, 2009, Morphological processing of principal orthogonal modesfor crack detection in beam structures, Journal of Mechanics of Materials and Structures, V4(6), pp. 1063-1088.
J.32)

K. Gryllias, I. A. Antoniadis, 2009,  A peak energy criterion (PE) for the selection of resonance bands in complex shifted morlet wavelet (CSMW) based demodulation of defective rolling element bearings vibration response, International Journal of Wavelets, Multiresolution and Information Processing, V7(4), pp. 387-410.
J.31)

K.Gryllias, C.Yiakopoulos, I. A. Antoniadis, 2009, Application of Morphological Analysis for Gear Fault Detection and Trending, Diagnostyka, Vol. 48(4), pp. 37-42.
J.30)
 F.G.Papaspiridis, I. A. Antoniadis, 2008, “Dielectric Elastomer Actuators as elements of active vibration control systems”, Advances in Science and Technology, Vol. 61, pp. 103-111.
J.29)

G.N.Glossiotis, I. A. Antoniadis, 2007, Digital Filter Based Motion Command Preconditioning of Time Varying Suspended Loads in Boom Cranes for Sway Suppression, Journal of Vibration and Control, Vol. 13(5), pp. 617-656.
J.28)

G.N.Glossiotis, I. A. Antoniadis, 2007, Vibration suppression of structures with densely spaced modes using maximally robust minimum delay digital finite impulse response filters, Journal of Sound and Vibration, Vol. 300(3-5), pp. 612-643.
J.27)

A.N.Lioulios, , I. A. Antoniadis,  2006, Effects of rotational speed fluctuations on the dynamic behaviour of rolling element bearings with radial clearances, International Journal of Mechanical Sciences, Vol 48, pp. 809-829.
J.26)

Patargias T. I., Yiakopoulos C. T., Antoniadis I. A., 2006, Performance assessment of a morphological index in fault prediction and trending of defective rolling element bearings, Nondestructive Testing and Evaluation, Vol. 21, No 1, pp. 39-60.
J.25)

C. Yiakopoulos, I. Antoniadis, 2006, Cyclic bispectrum patterns of defective rolling element bearing vibration response, Forschung im Ingenieurwesen, Vol. 70, pp. 90-104.
J.24)

C. Yiakopoulos, I. Antoniadis, 2005, Application of Some Advanced Signal Processing Techniques for Rolling Element Bearing Fault Detection, Diagnostyka, Vol. 36, pp. 33-39.
J.23)

I. Antoniadis, 2005, Modeling And Simulation Of A Power Plant Lignite Bunker Filling Process Using Hybrid Interpreted Petri Nets, Proc. Instn Mech. Engineers, Vol 217, Part E, J. of Process Mechanical Engineering, pp. 375-383.
J.22)

C. Yiakopoulos, K.Gryllias, I. Antoniadis, 2005, Spectral effects of the slip motion in defective rolling element bearings, Advances in Vibration Engineering, V4(2), 199-211.
J.21)

D Economou, C.Mavroidis, I. Antoniadis, 2004, Robust vibration suppression in flexible systems using Infinite Impulse Response (IIR) Digital Filters, AIAA Journal of Guidance, Control and Dynamics, V27(1), pp. 107-117.
J.20)

G.Glossiotis, I. Antoniadis, 2003, Payload sway suppression in rotary cranes by digital filtering the commanded inputs, Proc. Instn Mech. Engineers, Vol 217, Part K J. of Multibody Dynamics, pp. 99-109.
J.19)

N.Nikolaou, I. Antoniadis, 2003, Application of morphological operators as envelope extractors for impulsive type periodic signals, Mechanical Systems and Signal Processing Journal, V17(6), pp. 1147-1162.
J.18)

C. Yiakopoulos, I. Antoniadis, 2002, Wavelet based demodulation of Vibration Signals generated by defects in roller bearings, Shock and Vibration Journal, V9 (2002), pp 293-306.
J.17)

N. Nikolaou, I. Antoniadis, 2002, Demodulation of Vibration signals generated by defects in Rolling element bearings using Complex Shifted Morlet Wavelets, Mechanical Systems and Signal Processing, V16(4), pp. 677-694.
J.16)

D. Economou, C. Mavroidis, I. Antoniadis, C. Lee, 2002, Maximally robust input preconditioning for residual vibration suppression using low pass FIR digital filters, Journal of Dynamic Systems, Measurement and Control, Transactions of the ASME, V124(1), pp. 85-97.
J.15)

N. Nikolaou, I. Antoniadis,  2002, Rolling element  bearing fault diagnosis using wavelet  packets, NDT&E International, Vol. 35(3), pp.197-205.
J.14)

I. Antoniadis, G. Glossiotis, 2002, Cyclostationary analysis of rolling element bearing vibration signals, Journal of Sound and Vibration, 248(5), 829-845.
J.13)

I. Antoniadis, D. Economou, 2001, Robust residual Vibration suppression for Linear Time Invariant Systems by digital filtering of the guidance function, Mechanical Systems and Signal Processing, 15(3), 565-580.
J.12)

Α. Hountras, I. Antoniadis, A. Kanarachos, 2000, Application of N-Step-Ahead Neurocontrol on Articulated Manipulators, Journal of Robotic Systems, 17(3), 127-148.
J.11)

I. Antoniadis, 1999, Guidance Preconditioning by an Impulse Sequence for Robust Residual Vibration Suppression, Shock and Vibration Journal, 6, 133-145.
J.10)

Α. Hountras, I. Antoniadis, A. Kanarachos, 1999, Implementation of N-Step-Ahead Neurocontrol on 3Axes Heavy Duty Hydraulic Manipulator, Mechatronics Journal, 9, 235-270.
J.9)

I. Antoniadis, A. Kanarachos, 1996, Splines-Based Guidance with enhanced frequency robustness for the motion of flexible part handling manipulators, Mechatronics Journal, 6(7), 761-777.
J.8)

Ι. ΑντωνιÜδης, 1995, Προσδιορισμüς αρμονικþν συνιστωσþν σημÜτων σε γενικÜ περιβÜλλοντα θορýβου: η μÝθοδος HARD, Eπιστ. Εκδüσεις ΤΕΕ/IV, τευχ. 1-2, 7-18.
J.7)

A. Kanarachos, I. Antoniadis, E. Bekiaris, 1994, Application of the Digital Signal Processing Methodology (DSPM) for the design of time integration formulae, Computational Mechanics Jοurnal, 15, 79-99.
J.6)

I. Antoniadis, A.Kanarachos, 1994, Introduction of the Digital Signal Processing Methodology (DSPM) for time integration, Engineering Computations Journal, 11, 457-476.
J.5)

I. Antoniadis, A. Kanarachos, 1988, Decoupling Procedures for fluid-structure interaction problems, Computer Methods in Applied Mechanics and Engineering, 70, 1-25.
J.4)

I. Antoniadis, A.Kanarachos, 1988, Modal Decoupling Methods for fluid-structure interaction in piping systems, Computers and Structures, 29(4), 577-585.
J.3)

A. Kanarachos, I. Antoniadis, 1988, Symmetric variational principles and modal methods in fluid-structure interaction problems, Journal of Sound and Vibration, 121(1), 77-104.
J.2)

I. Antoniadis, A. Kanarachos, 1987, A decoupling procedure for the modal analysis of structures in contact with incompressible fluids, Communications in Applied Numerical Methods, Vol. 3, 507-517.
J.1)

A. Kanarachos, I. Antoniadis, 1987, Analyse und Optimierung von FEM-Strukturen mit CADOP, CAE Journal, 3/87, 60-67.

 

CONFERENCE PROCEEDINGS

C.127)

Georgios Mousmoulis, Christos Yiakopoulos, Ioannis Kassanos, Ioannis Antoniadis, John Anagnostopoulos, ‘Vibration and acoustic emission monitoring of a centrifugal pump under cavitating operating conditions’, 8th IAHR International Workshop on Cavitation and Dynamic Problems in Hydraulic Machinery and Systems, 9-11 October 2019, Stuttgart, Germany.
C.126)

Kapasakalis K.A., Sapountzakis E.J. and Antoniadis I. A. (2019) “Implementation of the KDamper Concept for Base Isolation to a Typical Concrete Building Structure”, Proc. of the 12th International Congress on Mechanics 12HSTAM2019, Thessaloniki, Greece, 22-25 September.
C.125)

Κ. ΚαπασακÜλης, Ι. ΑντωνιÜδης, Ε. ΣαπουντζÜκης (2019) “Καινοτüμα ΣυστÞματα Μüνωσης με Στοιχεßα ΑρνητικÞς Στιβαρüτητας για τη ΣεισμικÞ Προστασßα των Κατασκευþν”, 4ο ΠανελλÞνιο συνÝδριο ΑΝΤΙΣΕΙΣΜΙΚΗΣ ΜΗΧΑΝΙΚΗΣ ΤΕΧΝΙΚΗΣ ΣΕΙΣΜΟΛΟΓΙΑΣ, ΑθÞνα, ΕλλÜδα, 5-7 Σεπτεμβρßου 2019.
C.124)

Kapasakalis K.A., Antoniadis I. A. and Sapountzakis E.J (2019) “KDamper Concept for Base Isolation and Damping of High-Rise Building Structures”, Proc. of the 14th International Conference on Vibration Problems ICOVP 2019, Crete, Greece, 1-4 September.
C.123)

Kapasakalis K.A., Alamir C.H.T., Antoniadis I. A. and Sapountzakis E.J (2019) “Frequency Based Design of the KDampr Concept for Seismic Isolation of Bridges”, Proc. of the 14th International Conference on Vibration Problems ICOVP 2019, Crete, Greece, 1-4 September.
C.122)

Bollano P.O.N, Kapasakalis K.A., Sapountzakis E.J. and Antoniadis I. A. (2019) “KDamper Concept for Base Isolation and Damping of High-Rise Building Structures”, Proc. of the 14th International Conference on Vibration Problems ICOVP 2019, Crete, Greece, 1-4 September.
C.121)

Kapasakalis K.A., Antoniadis I. A. and Sapountzakis A.E (2019) “Implementation of the KDamper Concept for Seismic Protection of Bridges”, Proc. of the 14th International Conference on Vibration Problems ICOVP 2019, Crete, Greece, 1-4 September.
C.120)

Paradeisiotis, I. A. Antoniadis, Implementation of a Low Frequency Acoustic Isolation Panel Incorporating KDamper Based Mounts, Proceedings of ICOVP2019, (2019).
C.119)

A. Paradeisiotis, C. Yiakopoulos, I. A. Antoniadis, A Modular Concept for Quite Zone Generation in Transportation Media with Multiple Seat Configurations, Proceedings of ICOVP2019, (2019).
C.118)

Kapasakalis K.A., Sapountzakis, E.J. and Antoniadis I. A. (2019) “Control of Multi Storey Building Structures with a New Passive Vibration Control System Combining Base Isolation with KDamper”, Proc. of the 7th International Conference on Computational Methods in Structural Dynamics and Earthquake Engineering COMPDYN 2019, Crete, Greece, June 24-26.
C.117)

Antoniadis I. A., Kapasakalis K.A. and Sapountzakis E.J. (2019) “Isolation or Damping? A Soil-dependent approach based on the KDamper concept”, Proc. of the 2nd International Conference on Natural Hazards & Infrastructure ICONHIC 2019, Crete, Greece, June 23-26.
C.116)

Sapountzakis E.J., Kapasakalis K.A. and Antoniadis I. A. (2019) “Negative stiffness Elements in Seismic Isolation of Bridges”, Proc. of the 2nd International Conference on Natural Hazards & Infrastructure ICONHIC 2019, Crete, Greece, June 23-26.
C.115)

Antoniadis I. A., Kapasakalis K.A. and Sapountzakis E.J. (2019) “Advanced Negative Stiffness Absorbers for the Seismic Protection of Structures”, Proc. of the International Conference on Key Enabling Technologies 2019 KEYTECH2019, Istanbul, Turkey, 24-26 April 2019.
C.114)

I. A. Antoniadis, A. Paradeisiotis, A periodic acoustic meta-material concept incorporating negative stiffness elements for low-frequency acoustic insulation/absorption, Proceedings of ISMA2018, (2018).
C.113)

A. Paradeisiotis, C. Yiakopoulos, I. A. Antoniadis, A compact and light acoustic transducer using dielectric elastomer films for low frequency active noise cancellation, Proceedings of ISMA2018, (2018).
C.112)

K.Gryllias.   Sapountzakis I.E., Tranakidis P.G. and Antoniadis I.A. (2017) ‘’Impact Absorption using the KDamper Concept’’, Proc. of the 20th International Conference on Composite Structures, Paris, France, 4-7 September.
C.111)

I. A. Antoniadis, C.Yiakopoulos, (2017). Demodulation of vibration signals generated by defects in rolling element bearings under variable speed using morphological analysis and complex shifted Morlet wavelets. Surveillance 9 International Conference.
C.110)

P.Syrimi, E.Sapountzakis, G.Tsiatas, I. A. Antoniadis, (2017). Parameter Optimization of the KDamper Concept in Seismic Isolation of Bridges Using Harmony Search Algorithm. COMPDYN 2017, 10.7712/120117.5408.17764.
C.109)

T.Ampatzidis, D.Chronopoulos, I. A. Antoniadis, (2017). Examination of acoustic insulation of composite metamaterials with negative stiffness elements inclusions, 24th International Conference on Sound and Vibration, 23-27 July 2017, London UK.
C.108)

I. A. Antoniadis, 2016, “Towards the design of highly dissipative low?frequency metamaterials: the KDamping concept”, AMM16, 1st Int. Conference on Advances in Mechanical Metamaterials, 10-11 October 2016 Trento, Italy, INVITED PAPER.
C.107)

Antoniadis I. A., Georgoutsos, V., Paradeisiotis, A., Kanarachos, S., & Gryllias, K. (2016, September). Analysis and evaluation of energy converters based on multi-axis inertial reaction mechanisms. In International Conference On Noise And Vibration Engineering, ISMA2016, Leuven, Belgium (September 2016) (pp. 667-680).
C.106)

Yiakopoulos, K. Gryllias, M. Chioua, M. Hollender, I. A. Antoniadis, 2016, “Advanced analysis tools for early anomaly detection and visualization in large scale complex industrial installations”, EUROMAINTENANCE2016, 30/05/-01/06/2016, Athens, Greece.
C.105)

Sapountzakis I.E., Tranakidis P., Antoniadis I. A., Kanarachos S.A. and Gryllias K., 2016, “KDamping: A Stiffness Based Passive Damping Concept’’, Proc. of the 27th ISMA 2016 International Conference on Noise and Vibration Engineering, Leuven, Belgium, 19-21 September.
C.104)

I. A. Antoniadis, V. Georgoutsos, A.Paradeisiotis, S.Kanarachos, K.Gryllias, 2016, “Analysis and evaluation of energy converters based on multi-axis inertial reaction mechanisms”,Proc. of the 27th ISMA 2016 International Conference on Noise and Vibration Engineering, Leuven, Belgium, 19-21 September.
C.103)

I. A. Antoniadis, V. Georgoutsos, A.Paradeisiotis, S.Kanarachos, K.Gryllias, 2016, “Preliminary assessment of a wave energy conversion principle, using fully enclosed multi-axis inertial reaction mechanisms”, ICSV23 -23rd International Congress on Sound and Vibration, Athens, Greece, 10-14/07/2016.
C.102)

Antoniadis I. A., Sapountzakis I.E. and Chatzi E., 2016, ”A KDamping Concept for Seismic Excitation Absorption’’, Proc. of the 1st ICONHIC 2016 International Conference on Natural Hazards and Infrastructure, Chania, Crete, Greece, 28-30 June.
C.101)

Sapountzakis I.E., Antoniadis I. A., Kanarachos S.A. and Gryllias K. (2016) ‘’KDamping: A Novel Stiffness Based Vibration Absorption Concept’’, Proc. of the Final Conference TUD COST ACTION TU1105, Elche, Spain, 6-7 April.
C.100)

I. A.Antoniadis, V. Georgoutsos, A.Paradeisiotis, 2016, “Energy conversion with multi-axis inertial reaction mechanisms, Proc. of the 11th HSTAM 2016 International Congress on Mechanics, Athens, Greece, 27-30 May.
C.99)

Antoniadis I.A., Sapountzakis I.E., 2016, ‘’Base Acceleration Absorption of Structures Using the KDamper Concept’’, Proc. of the 11th HSTAM 2016 International Congress on Mechanics, Athens, Greece, 27-30 May.
C.98)

Sapountzakis I.E., Antoniadis I.A., Kanarachos S.A. and Gryllias K., 2016, ”KDamping: A Novel Stiffness Based Vibration Absorption Concept”, Proc. of the Final Conference TUD COST ACTION TU1105, Elche, Spain, 6-7 April.
C.97)

I. A. Antoniadis, V.Georgoutsos, 2015, “Wave energy conversion with fully enclosed multi-axis inertial reaction mechanisms”, DSTA2015, 13th INTERNATIONAL CONFERENCE, Dynamical Systems – Theory and Applications, 7-10/12/2015. Lodz, POLAND.
C.96)

I. A. Antoniadis, K.J.Kyriakopoulos, E.G.Papadopoulos, 2015, “Hyperdamping properties of a novel stable non-linear oscillator concept, based on a statically unstable stiffness element”, DSTA2015, 13th
INTERNATIONAL CONFERENCE, Dynamical Systems - Theory and Applications, 7-10/12/2015. Lodz, POLAND.
C.95)

K. C. Gryllias, I. A. Antoniadis, C. T. Yiakopoulos, 2015, 'A novel semi-supervised mathematical morphology-based fault detection & classification method for rolling element bearings', 22th International Congress on Sound and Vibration (ICSV22), 2015, Florence, Italy.
C.94)

A. Lalas, V. K. Dertimanis, I. A. Antoniadis and E. N. Chatzi, 2015, “Considerations towards the application of low-frequency locally resonant metamaterials for earthquake hazard mitigation”, Engineering Mechanics Institute International Conference 2015, The Hong-Kong Polytechnic University, 7-9/01/2015.
C.93)

Konstantinos C. Gryllias, Christos T. Yiakopoulos, Ioannis A. Antoniadis, 'Output-Only Modal Analysis using IFESIS', 4th International Conference on Condition Monitoring of Machinery in Non-stationary Operations (CMMNO), 2014, Lyon, France.
C.92)

I.Antoniadis, 2014, “Physical concepts for the integration of Dielectric Elastomers in scalable energy conversion applications”, EAP Workshop 2014, Electromechanically Active Polymer (EAP) transducers & artificial muscles, Queen Mary University of London, 25-26 November 2014.
C.91)

I. Antoniadis, D. Chronopoulos, V. Spitas, D. Koulocheris, 2014, “Hyper-damping properties of oscillators and meta-materials with negative stiffness elements”, ISMA2014 - International Conference on Noise and Vibration Engineering, 15-17/9/2014, Leuven, Belgium, paper 727.
C.90)

I. Antoniadis, C. T. Yiakopoulos, K. C. Gryllias, K I. Rodopoulos, 2013, “IFESIS: Instantaneous Frequencies Estimation via Subspace Invariance properties of wavelet Structures”,Surveillance 7, Institute of Technology of Chartres, France, October 29-30, 2013, MSSP BEST PAPER AWARD.
C.89)

I. A. Antoniadis, D.T. Venetsanos, F.G. Papaspyridis, 2013, “Dynamic properties of a class of planar pre-stressed tensegrity elastomer structures”, EuroEAP 2013, Third International conference on Electromechanically Active Polymer (EAP) transducers & artificial muscles, 26-28 June 2013, Duebendorf (Zurich), Switzerland.
C.88)

I. A. Antoniadis, K.Rodopoulos, C.Yiakopoulos, “Multiple Instantaneous Frequency estimation using Complex Shifted Morlet Wavelets", CM 2013/MFPT 2013, Krakow, Poland, 18-20 June 2013.
C.87)

I. A. Antoniadis, D.T. Venetsanos, F.G. Papaspyridis, I.E.Sapountzakis, 2013, “Dynamic non-linear energy absorbers based on properly stretched in-plane asymmetric elastomer structures”,10th HSTAM International Congress on Mechanics, Chania, Greece, 25-27/5/ 2013.
C.86)
 F.Papaspyridis, D. Venetsanos,  I. Antoniadis, 2012, ‘Dynamic non-linear energy absorbers based on dielectric elastomers’, EuroEAP 2012, International conference on Electromechanically Active Polymer (EAP) transducers & artificial muscles, Potsdam, Germany, 29-30 May 2012.
C.85)
 K.Rodopoulos, C.Yiakopoulos, I. Antoniadis, 2011, A parametric approach for the estimation of the instantaneous speed of rotating machinery, Surveillance 6, 6th International Conference on Acoustical and Vibratory Surveillance, Methods and Diagnostic Techniques, Compiegne, France, October 25-26.
C.84)
 K.C.Gryllias, I. A. Antoniadis, 2010, Modelling and experimental analysis of a 6-High industrial rolling mill vibration response, The Seventh International Conference on Condition Monitoring and Machinery Failure Prevention Technologies CM2010/MFPT 2010, Stratford on Avon, UK, 22-24 /6/2010.
C.83)
 K.C.Gryllias, C.T.Yiakopoulos, I. A. Antoniadis, 2009, Automated diagnostic approaches for defective rolling element bearings using minimal training pattern classification methods, 4th World Congress on Engineering Asset Management and Intelligent Maintenance Systems, 28-30/9/2009, Athens, Greece.
C.82)
 C.T.Yiakopoulos, K.C.Gryllias, I. A. Antoniadis, 2009, Instantaneous frequency estimation in rotating machinery using a harmonic signal decomposition (HARD) parametric method, ASME 2009 International Design Engineering Technical Conferences & Computers and Information in Engineering Conference IDETC/CIE 2009, August 30 - September 2, 2009, San Diego, California, USA.
C.81)
 C.T.Yiakopoulos,K.C.Gryllias, I. A. Antoniadis, 2009, Rolling element bearing fault classification using k-means frequency domain based clustering, ASME 2009 International Design Engineering Technical Conferences & Computers and Information in Engineering Conference IDETC/CIE 2009, August 30 - September 2, 2009, San Diego, California, USA.
C.80)
 K.C.Gryllias, I. A. Antoniadis, 2009, Αpplication of the Energy Operator Separation Algorithm (EOSA) for the instantaneous amplitude and frequency calculation of nonlinear dynamic systems response, ASME 2009 International Design Engineering Technical Conferences & Computers and Information in Engineering Conference IDETC/CIE 2009, August 30 - September 2, 2009, San Diego, California, USA.
C.79)
 K.C.Gryllias, I. A. Antoniadis, 2009, Comparison of criteria for optimal demodulation of defective rolling element bearings vibration response with Complex Shifted Morlet Wavelets (CSMW), The Sixteenth International Congress on Sound and Vibration ICSV16, Krakow, Poland, 5-9 July 2009.
C.78)
 K.C.Gryllias, C.T.Yiakopoulos, I.A.Antoniadis, R.Guminski, S.Radkowski, 2009, A morphological index for fault detection and trending in defective gearboxes, The Sixteenth International Congress on Sound and Vibration ICSV16, Krakow, Poland, 5-9 July 2009.
C.77)
 K.C.Gryllias, C.T.Yiakopoulos, I. A. Antoniadis, 2009, Demodulation of Defective Rolling Element Bearings Vibration Response with Complex Shifted Wavelets (CSMW) using a Peak Energy Criterion (PEC), The Sixth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies CM2009/MFPT 2009, Dublin, Ireland, 23-25 June 2009.
C.76)
 K.C.Gryllias, C.T.Yiakopoulos, I. A. Antoniadis, S. Radkowski*, Sz. Gontarz, 2009, Doppler Effect minimization in the spectra emitted by moving vehicles by the application of a Harmonic Signal Detection (HARD) method, The Sixth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies CM2009/MFPT 2009, Dublin, Ireland, 23-25 June 2009.
C.75)
 K.C.Gryllias, C.T.Yiakopoulos, I. A. Antoniadis, 2009, Effects of input features on Support Vector Machine based rolling element bearing fault detection and trending, ECCOMAS Thematic Conference on Computational Methods in Structural Dynamics and Earthquake Engineering COMPDYN 2009, Rhodes, Greece, 22–24 June 2009.
C.74)
 Γ.ΖαννÞς, Ι. ΑντωνιÜδης, Μ.Φοýντη, 2008, “ΥπÝρλεπτη πουδροποßηση για παρασκευÞ ειδικþν επιχρισμÜτων απü απορρßματα μαρμÜρου”, 1o ΠανελλÞνιο ΣυνÝδριο Δομικþν Υλικþν και Στοιχεßων, 21-23 Μαßου 2008.
C.73)
 I. A. Antoniadis, 2008, ‘Morphological Processing of vibration signals resulting from defective structural and machine elements’, 4th International Congress on Technical Diagnostics, 9-12/09/2008, Olsztyn, Poland.
C.72)
 K. C. Gryllias, C.T.Yiakopoulos, I. A. Antoniadis, 2008, ‘Support Vector Macines and Cluster Analysis for fault detection and classification of rotating equipment’, Fifth International Conference on Condition Monitoring & Machinery Failure Prevention Technologies, 15-18/7/2008, Edinburgh, UK.
C.71)
 C.T.Yiakopoulos, K.C. Gryllias, I. A. Antoniadis, M.Zawisza, 2008, ‘Application of vibration based time domain indices for fault trending of damaged gears”, VII International Technical Systems Degradiation Seminar, 26-29/3/2008, Liptovsky Mikulas, Slovakia.
C.70)
 C.T.Yiakopoulos, K.C. Gryllias, I. A. Antoniadis, M.Jasinski, 2008, ‘Application of cyclostationary analysis for fault trending of damaged gears”, VII International Technical Systems Degradiation Seminar, 26-29/3/2008, Liptovsky Mikulas, Slovakia.
C.69)
 Γιακüπουλος Χ., Γρýλλιας Κ., Βüσου Κ., Προβατßδης Χ., ΑντωνιÜδης Ι., 2007, ΔιÜγνωση Βλαβþν Μηχανþν και Κατασκευþν, Ημερßδες για την επιστημονικÞ Ýρευνα στο Ε.Μ.Π. (Πυθαγüρας), ΠλωμÜρι, Ν. ΛÝσβος, 05-08/07/2007.
C.68)
 K.C. Gryllias, I. A. Antoniadis, 2007, ‘Application οf Support Vector Machines for Fault Detection and Classification of Defective Rolling Element Bearings’, Fourth International Conference on Condition Monitoring, 11-12/6/2007, Harrogate, UK.
C.67)
 K.C. Gryllias, I.N. Koukoulis, C.T. Yiakopoulos, I. A. Antoniadis and C. G. Provatidis, 2007, ‘Combination of proper orthogonal decomposition and morphological processing for crack detection in structures’, COMPDYN 2007, Rethymno, Crete, Greece, 13-16/06/2007.
C.66)
 A.Datta, S.Patel, C.Mavroidis, I.Antoniadis, J.Krishnasamy, M.Hosek, 2006, Fault diagnostics of industrial robots using support vector machines and discrete wavelet transforms, 2006 ASME International Mechanical Engineering Congress and Exposition, IMECE 2006, November 5-10 2006, Chicago, Illinois, USA.
C.65)
 K. Sardi, C. Yiakopoulos, K. Gryllias, I. Antoniadis, M. Founti, 2006, ‘Vibration analysis and combustion performance of an industrial drying facility’, poster No. 2A58 – Stationary Power Systems, 31st International Symposium on Combustion, The combustion Institute, Heidelberg, Germany, 6-11/8/2006.
C.64)
 G.Glossiotis, I. A. Antoniadis, 2006, ‘Application of digital filter based motion command preconditioning methods for vibration suppression of a flexible truss with densely spaced modes’, 13th International Congress on Sound and Vibration ISCV13, Vienna, Austria, 2-6/7/2006.
C.63)
 T. Patargias, C. Yiakopoulos, I. A. Antoniadis, 2006,‘Trending analysis of defective rolling element bearings using a morphological index’, 13th International Congress on Sound and Vibration ISCV13, Vienna, Austria, 2-6/7/2006.
C.62)
 K. Gryllias, I. Koukoulis, C. Yiakopoulos, C. Provatidis, I. A. Antoniadis, 2006, ‘Crack detection in structures using proper orthogonal decomposition and morphological processing’,13th International Congress on Sound and Vibration ISCV13, Vienna, Austria, 2-6/7/2006.
C.61)
 C.Yiakopoulos , I. Antoniadis, 2005, ISO Standards for Condition Monitoring of Machines, 5ο Eθνικü SυνÝδριο NDT , ΕΛ.Ε.Μ.Κ.Ε (HSNT), 18-19/11/2005, ΑθÞνα, ΕλλÜδα.
C.60)
 C.T.Yiakopoulos, I. A. Antoniadis, 2005, ‘Application of Some Advanced Signal Processing Techniques for Rolling Element Bearing Fault Detection’, Wibro Tech 2005, Warsaw, Poland, 3-4/11/2005.
C.59)
 C.Yiakopoulos, I. Antoniadis, 2005, Sensitivity Analysis οf αn Information Maximization Approach to the Blind Separation of the Vibration Responses of Defective Rolling Element Bearings’, IDETC/CIE 2005, ASME 2005 International Design Engineering Technical Conferences & Computers and Information in Engineering Conference, September 24-28, Long Beach, California, USA.
C.58)
 G.Glossiotis, I. Antoniadis, 2005, Maximally Robust Sway Free Point-To-Point Transportation Of Boom Crane Loads, By A Fir Filtering Approach Of The Motion Commands, IDETC/CIE 2005, ASME 2005 International Design Engineering Technical Conferences & Computers and Information in Engineering Conference, September 24-28, Long Beach, California, USA.
C.57)
 A.Lioulios, I. Antoniadis, 2005, Stabilizing Effects Of Speed Fluctuations On The Dynamic Response Of Rolling Element Bearings With Radial Clearances, IDETC/CIE 2005, ASME 2005 International Design Engineering Technical Conferences & Computers and Information in Engineering Conference, September 24-28, Long Beach, California, USA.
C.56)
 G.Glossiotis, I. Antoniadis, 2005, Robust Payload Vibration Suppression In Rotary Cranes By Pre-Filtering The Commanded Inputs, ICSV12, 12th International Congress on Sound and Vibration, Lisbon, Portugal, 11-14 July.
C.55)
 C.Yiakopoulos, I. Antoniadis, 2005, Application Of Some Recent Signal Processing Techniques For Rolling Element Bearing Fault Detection, ICSV12, 12th International Congress on Sound and Vibration, Lisbon, Portugal, 11-14 July.
C.54)
 G.Glossiotis, I. Antoniadis, 2005, Digital Filter Based Maximally Robust and Time Optimal Vibration Free Motion of Structures with Densely Packed Modes, 5th GRACM International Congress on Computational Mechanics, Limassol, Cyprus, 29 June – 1 July.
C.53)
 C.Yiakopoulos, K.Gryllias, I. Antoniadis, 2004, Effects Of Slip Motion On The Cyclic-Bispectrum Of Defective Rolling Element Bearing Responses, Surveillance 5, 5th International Conference on Acoustical and Vibratory Surveillance, Methods and Diagnostic Techniques, Senlis, France, October 11-13.
C.52)
 C.Yiakopoulos, N.Nikolaou, I. Antoniadis,  2004, Sensitivity Of Time-Domain And Morphological Indices For Fault Detection And Trending Of Defective Rolling Bearings, Surveillance 5, 5th International Conference on Acoustical and Vibratory Surveillance, Methods and Diagnostic Techniques, Senlis, France, October 11-13.
C.51)
 C.Yiakopoulos, H.Dimou, I. Antoniadis,  2004, Blind Source Separation Methods in the Vibration Response of Defective Rolling Element Bearings, 29th ISMA 2004, Leuven, Belgium, pp. 2581-2595, September 20-22.
C.50)
 K. Gryllias, C.Yiakopoulos, I. Antoniadis, 2004, Spectral effects of the slip motion in defective rolling element bearings, 7th Greek National Congress on MECHANICS.
C.49)
 H.Dimou, C.Yiakopoulos, I. Antoniadis, 2004, Αpplication and comparison on blind source separation methods in the vibration response of defective rolling element bearings, 7th Greek National Congress on MECHANICS.
C.48)
 A. Houdras, I.Manousaridis, I. Antoniadis, 2002, Operational and control principles of the district heating retrofit at Megalopolis SES Unit III, , MEDPOWER 2002, Athens, Greece.
C.47)
 I. Antoniadis, 2002, Modelling and simulation of a Power Plant Lignite Bunker Filling Process, combining Hybrid and Interpreted Petri Nets, MEDPOWER 2002, Athens, Greece.
C.46)
 G.Glossiotis, C.Yiakopoulos, I. Antoniadis, 2002, A real time open architecture multichannel dynamic signals measurement and processing system, 1st Hellenic Symposium on Acoustics, Patras, Greece.
C.45)
 I. Antoniadis, C.Yiakopoulos, G.Glossiotis, 2002, Cyclostationary signal processing applications in industrial measurements, 1st Hellenic Symposium on Acoustics, Patras, Greece.
C.44)
 N.Nikolaou, I. Antoniadis, 2002, Application of Morphological Filters in impulsive type signal analysis, 1st Hellenic Symposium on Acoustics, Patras, Greece.
C.43)
 C.Yiakopoulos, I.Antoniadis, 2002, Analysis of vibration responses of defective rolling bearings using Blind Source Separation, 2nd WSEAS Int. Conf. On Signal, Speech and Image Processing, Skιathos, Greece.
C.42)
 N. Nikolaou, I.Antoniadis, 2002, Non-linear wavelet packet denoising of impulsive vibration signals, 2nd WSEAS Int. Conf. On Signal, Speech and Image Processing, Skιathos, Greece.
C.41)
 N. Nikolaou, I. Antoniadis, 2002, Application of a morphological filter in bearing vibration signal analysis, COMADEM 2002, Birmingham, UK.
C.40)
 C.Yiakopoulos, I. Antoniadis, 2002, Rolling Element Vibration Signal Processing using the Cyclic Bispectrum, COMADEM 2002, Birmingham, UK.
C.39)
 I. Antoniadis, V.Leopoulos, 2002, Application of Petri Nets as an operational and reliability analysis tool for criticality based Maintenance, COMADEM 2002, Birmingham, UK.
C.38)
 G. Glossiotis, E.Pantazidis, I. Antoniadis, 2002, Preliminary description and capabilities assessment of a piezoelectrically driven micro-robot for the internal inspection of small diameter pipes, 12th International Symposium on Measurement and Control in Robotics, Bourges France.
C.37)
 D. Economou, C. Mavroidis, I. Antoniadis, 2002, Comparison of filter types used for command preconditioning in vibration suppression applications, American Control Conference, Anchorage, USA.
C.36)
 I. Antoniadis, A.Hountras, G.Glossiotis, 2002, Design and Installation of an on-line mechanical parameters monitoring system for a Diesel Generator Unit Set, NIDays 2001-2002.
C.35)
 N. Nikolaou, I. Antoniadis, 2001, Demodulation of rolling element bearing vibration signals using the Continuous Wavelet Transform, 4th International Conference on Acoustical and Vibratory Surveillance, Methods and Diagnostic Techniques, Compiegne, France.
C.34)
 I. Antoniadis, G. Glossiotis, 2001, Cyclostationary analysis of rolling element bearing vibration signals, 4th International Conference on Acoustical and Vibratory Surveillance, Methods and Diagnostic Techniques, Compiegne, France.
C.33)
 D. Economou, C. Mavroidis, I. Antoniadis, 2001, Proper Filter Design Procedure for Vibration Suppression Using  Delay-Error-Order Curves, ASME Paper No. IMECE2001/DSC-24614, 2001 ASME International Symposium on Advances in Robot Dynamics and Control, ASME International Mechanical Engineering Congress and Exposition, NY, USA.
C.32)
 D. Economou, I. Antoniadis, 2001, Sway Suppression of Suspended Payloads With Hoisting Using Digital Filters, ASME Paper No. IMECE2001/DSC-24608, 2001 ASME International Symposium on Advances in Robot Dynamics and Control, ASME International Mechanical Engineering Congress and Exposition, NY, USA.
C.31)
 G. Glossiotis, I. Antoniadis, 2001, Cyclostationary analysis of rolling element bearing vibration signals, ASME Paper No. DETC2001/VIB-21759, “Fault Detection/Diagnostics in Rotating Machinery” symposium of the 18-th Biennial ASME Conference on Mechanical Vibration and Noise, Pittsburg, USA.
C.30)
 C. Yiakopoulos, I. Antoniadis, 2001, Wavelet based demodulation of vibration signals generated by defects in rolling element bearings, ASME Paper No. DETC2001/VIB-21758, “Fault Detection/Diagnostics in Rotating Machinery” symposium of the 18-th Biennial ASME Conference on Mechanical Vibration and Noise, Pittsburg, USA.
C.29)
 D. Economou, C. Mavroidis, I. Antoniadis, 2001, Comparison of robust residual vibration suppression capabilities of conventional digital filters, ASME Paper No. DETC2001/VIB-21472, “Active and hybrid vibration control” symposium of the 18-th Biennial ASME Conference on Mechanical Vibration and Noise, Pittsburg, USA.
C.20)
 N. Nikolaou, I. Antoniadis, 2001, A time-frequency envelope estimation method for detectionof bearing-localized defects, ASME Paper No. DETC2001/VIB-21006, “Wavelet and Time-Frequency Analysis and Applications” symposium of the 18-th Biennial ASME Conference on Mechanical Vibration and Noise, Pittsburg, USA.
C.27)
 I. Katsikas, I. Katsoulis, I. Antoniadis, 2001, Design Considerations and prototype implementation of a piezoelectrically driven micro-vehicle for the internal inspection of small diameter pipes, 5th WSES/IEEE International Conference on Systems, Rethymnon, Greece.
C.26)
 N. Nikolaou, I. Antoniadis, 2001, Bearing Fault Diagnosis Using Shifted Wavelet Filters, 5th WSES/IEEE International Conference on Systems, Rethymnon, Greece.
C.25)
 D. Economou, I. Antoniadis, 2001, Vibration Reduction of Gantry Crane Loads with Hoisting Using Finite Impulse Response (FIR) Digital Filters, 5th WSES/IEEE International Conference on Systems, Rethymnon, Greece.
C.24)
 N. Nikolaou, I. Antoniadis, 2001, Application of Wavelet Packets in Bearing Fault Diagnosis, 5th WSES/IEEE International Conference on Multirate Systems and Signal Processing, Rethymnon, Greece.
C.23)
 D. Economou, C. Mavroidis, I. Antoniadis, 2001, Experiments on Robust Vibration Suppression in Mechatronic Systems Using IIR Digital Filters, 2001 IEEE/ASME International Conference on Advanced Intelligent Mechatronics,  (AIM '01), Como, Italy.
C.22)
 D. Economou, C. Mavroidis, I. Antoniadis, 2001, Robust residual vibration suppression using IIR filters, IFAC Symposium on System Structure and Control, Prague, Czech Republic.
C.21)
 D. Economou, C. Lee, C. Mavroidis, I. Antoniadis, 2001, Experimental demonstration of input preconditioning for residual vibration suppression using low-pass FIR digital filters, American Control Conference, Arlington, USA.
C.20)
 I. Antoniadis, G. Glossiotis, 2001, Cyclostationary analysis of rotating machinery dynamic response signals, 4th European Conference on Noise Control/EURONOISE 2001, Patras, Greece.
C.19)
 N. Nikolaou, I. Antoniadis, 2001, Demodulation of impact generated transient signals using the Morlet Wavelet, 4th European Conference on Noise Control/EURONOISE 2001, Patras, Greece.
C.18)
 D. Economou, C. Lee, C. Mavroidis, I. Antoniadis, 2000, Robust Vibration suppression in flexible payloads carried by robot manipulators using digital filtering of Joint trajectories, 2nd International Symposium on Robotics and Automation, ISRA 2000, Monterrey, Mexico.
C.17)
 I. Antoniadis, V. Leopoulos, 2000, A concept for the integrated process description, PLC programming and simulation using Petri Nets, 2000 IEEE International conference on Systems, Man & Cybernetics/IEEE/SMC 2000, Nashville, U.S.A.
C.16)
 Α. Hountras, I. Antoniadis, A. Kanarachos, 1999, Control of a 3-Axes Heavy Duty Electrohydraulic Manipulator using neural networks, 3rd International Symposium on advanced electromechanical motion systems/ELECTROMOTION 99, Patras, Greece.
C.15)
 I. Antoniadis, V.Leopoulos, 1999, Simulation of a Discrete Event Industrial Electromechanical system using Petri nets,. 3rd International Symposium on advanced electromechanical motion systems/ELECTROMOTION 99, Patras, Greece.
C.14)
 I. Antoniadis, A.Kardasis, 1999, Integrated Modelling of the Slweing motion of a JIB crane, for the design of an anti-sway guidance function, 3rd International Symposium on advanced electromechanical motion systems/ELECTROMOTION 99, Patras, Greece.
C.13)
 Α. Hountras, I. Antoniadis, A. Kanarachos, 1999, N-Step-Ahead Neurocontrol of Articulated Manipulators, European Symposium on Intelligent Techniques, ESIT ’99, Chania, Greece.
C.12)
 I. Antoniadis, 1999, Guidance Preconditioning for Robust Residual Vibration Suppression: Impulse and ARMA sequence approaches, Vibration, Noise and Structural Dynamics ’99, Venice, Italy.
C.11)
 I. Antoniadis, 1999, Detection of Harmonic Components of Signals in General Noisy Environments: Comparison of HARD with other Parametric Methods, Vibration, Noise and Structural Dynamics ’99, Venice, Italy.
C.10)
 I. Antoniadis, V. Leopoulos, 1999, Integrated design, scheduling and automation of a production process using Petri Nets,  IMACS/IEEE CSCC 99, Athens, Greece.
C.9)
 I. Antoniadis, D.Economou, 1999, Robust residual vibration suppression by digital filtering the guidance function, 3rd National Congress on Computational Mechanics, Volos, Greece.
C.8)
 Ι. ΑντωνιÜδης, Χ. Γιακüπουλος, 1998, Σýγχρονες ΤεχνολογικÝς και ΕπιστημονικÝς ΜÝθοδοι ΔιÜγνωσης Βλαβþν Μηχανþν με ΑνÜλυση Κραδασμþν, ΑκουστικÞ Τεχνολογßα 1998, ΑθÞνα.
C.7)
 I. Antoniadis, 1998, Parametric Methods for the identification of Harmonic Components of Signals in General Noisy Environments: Presentation and Comparison in Mechanical Engineering Applications, 3rd International Conference on Acoustical and Vibratory Surveillance, Methods and Diagnostic Techniques, Senlis, France.
C.6)
 Α. Hountras, I. Antoniadis, A. Kanarachos, 1998, Implementation of N-Step-Ahead Neurocontrol in Engineering Applications,  SOFTCOM 98, IMACS/IFAC International Symposium on Soft Computing in Engineering Applications, Athens, Greece.
C.5)
 I. Antoniadis, 1998, Guidance preconditioning by an ARMA sequence for robust residual ibration suppression, 3rd European Robotics, Intelligent Systems and Control Conference/EURISCON 98, Athens, Greece.
C.4)
 I. Antoniadis, A. Kanarachos, 1995, Application of Robust Splines Based Guidance (RSBG) for the motion of flexible structures, 4th Greek National Congress on MECHANICS, Xanthi, Greece.
C.3)
 T. Georgakopoulos, P. Baltas, I. Antoniadis, 1994, Development of a 5 KWP One Axis Solar Tracking Structure for Utility Scale Photovoltaic Applications, European Conference on Renewable Energy Sources, 1994.
C.2)
 A. Kanarachos, I. Antoniadis, E. Bekiaris, R. Pollman, 1993, Informatics Technology as the missing link for the integration of people with special needs (PSN), 1st International Conference on Road Vehicle Automation, Bolton, U.K., 1993.
C.1)
 I. Antoniadis, A. Kanarachos, 1984, Modal Decoupling methods for linear fluid-structure interaction problems, EUROMECH 188, Fluid Loading and Fluid-Structure Interaction, LEEDS, U.K.

 

OTHER SCIENTIFIC JOURNALS AND BOOK CHAPTERS

P.15)
 Ι. ΑντωνιÜδης, 2012, ‘ΔΙΑΓΝΩΣΤΙΚΗ ΣΥΝΤΗΡΗΣΗ: Μαντεßα, Εμπειρßα Þ ΕπιστÞμη ...?’, 8th Maintenance Forum, 11-13/10/2012, ΑθÞνα.
P.14)
 Ι. ΑντωνιÜδης, 2009, ΣΥΝΕΧΙΖΟΜΕΝΗ ΕΚΠΑΙΔΕΥΣΗ ΜΗΧΑΝΙΚΩΝ: Προβληματισμοß και ΑναζητÞσεις, 3ο ΣυνÝδριο για τα τεχνικÜ Ýργα, ΙΔΙΠ-ΠΥ, ΕΕΔΕ, ΑθÞνα 10-11/12/2009.
P.13)
 Χ. Γιακüπουλος, Ι. ΑντωνιÜδης, 2006, ‘Πρüτυπα ISO για τον Ýλεγχο της λειτουργικÞς κατÜστασης μηχανολογικοý εξοπλισμοý’, ΤεχνικÞ Επιθεþρηση, Τεýχος 171, 7-8/2006, σελ. 32-36.
P.12)
 I. Antoniadis, A.Hountras, G.Glossiotis, 2003, Using NI LabVIEW and NI PXI for an Online Mechanical Parameters Monitoring System for a Diesel Generator Unit Set, NIDays, pp. 36-37.
P.11)
 C.Yiakopoulos, I. Antoniadis, 2002, Analysis of vibration responses of defective rolling element bearings using Blind Source Separation, N.E.Mastorakis, V.V.Kluev  (Eds), Advances in Multimedia, Video and Signal Processing Systems,  WSEAS Press, pp. 145-150.
P.10)
 N.Nikolaou, I. Antoniadis, 2002, Non-linear wavelet packet denoising of impulsive vibration signals, N.E.Mastorakis, V.V.Kluev  (Eds), Advances in Multimedia, Video and Signal Processing Systems,  WSEAS Press, pp. 339-344.
P.9)
 D. Economou, C. Mavroidis, I. Antoniadis, 2001, Robust Residual Vibration Suppression Using IIR Digital Filters, in “SYSTEM STRUCTURE AND CONTROL 2001”, Horacek (Ed), IFAC Publications, Elsevier Science Ltd.
P.8)
 I. Katsikas, I. Katsoulis, I.Antoniadis, 2001, Design Considerations and prototype implementation of a piezoelectrically driven micro-vehicle for the internal inspection of small diameter pipes, in “Advances in Systems Science: Measurement, Circuits and Control”, N.E.Mastorakis, L.A.Pecorelli-Pers  (Eds), World Scientific and Engineering Society Press, pp. 484-489.
P.7)
 N. Nikolaou, I. Antoniadis, 2001, Bearing Fault Diagnosis Using Shifted Wavelet Filters, in “Advances in Systems Science: Measurement, Circuits and Control”, N.E.Mastorakis, L.A.Pecorelli-Pers  (Eds), World Scientific and Engineering Society Press, pp. 449-454.
P.6)
 D. Economou, I. Antoniadis, 2001, Vibration Reduction of Gantry Crane Loads with Hoisting Using Finite Impulse Response (FIR) Digital Filters, in “Advances in Systems Science: Measurement, Circuits and Control”, N.E.Mastorakis, L.A.Pecorelli-Pers (Eds), World Scientific and Engineering Society Press, pp. 22-28.
P.5)

N. Nikolaou, I. Antoniadis, 2001, Application of Wavelet Packets in Bearing Fault Diagnosis, in “Advances in Scientific Computing, Computational Intelligence and Applications”, N.E.Mastorakis, V.Mladenov, B.Suter, L.J.Wang, (Eds) World Scientific and Engineering Society Press, pp. 12-19.

P.4)
 I. Antoniadis, V. Leopoulos, 1999, Integrated design, scheduling and automation of a production process using Petri Nets, in "Modern Applied Mathematics Techniques in Circuits, Systems and Control”, N.E.Mastorakis (ed.), World Scientific and Engineering Society Press, ch. 56, 359-365.
P.3)
 Α. Hountras, I. Antoniadis, A. Kanarachos, 1999, Engineering Applications of N-Step-Ahead Neurocontrol,  in “Advances in Intelligent Systems”, S.G.Tzafestas (ed.), Kluwer Academic Publishers, ch. 22, 235-246.
P.2)
 Ι. ΑντωνιÜδης, 1997, Σýγχρονες ΜÝθοδοι ΣυντÞρησης Βιομηχανικþν ΕγκαταστÜσεων, Δελτßο Π.Σ. Διπλωματοýχων Μηχανολüγων Ηλεκτρολüγων, 300/97, 58-65.
P.1)
 I. Antoniadis, 1980, Vibrationanalysisof a shaft system, Technical report P-80006-ALT-4, Aalborg Vaerft A/S, Denmark.